Address
304 North Cardinal
St. Dorchester Center, MA 02124
Work Hours
Monday to Friday: 7AM - 7PM
Weekend: 10AM - 5PM
CEMEDINE EP001K Elastic Epoxy Adhesive for Engineering Plastic Metal and Glass Bonding
CEMEDINE EP001K Elastic Epoxy Adhesive for Multi-Material Industrial Bonding
CEMEDINE EP001K Elastic Epoxy Adhesive is a two-part, room-temperature-curing adhesive developed for strong and flexible bonding across engineering plastics, metals, glass, ceramics, and other compatible materials. Unlike conventional epoxy systems that can become hard and brittle after curing, this elastic formulation combines epoxy adhesion with modified-silicone flexibility. The cured bond follows movement between different materials, helping reduce stress caused by vibration, impact, thermal expansion, contraction, and repeated temperature changes.
CEMEDINE EP001K Elastic Epoxy Adhesive is valuable when rigid adhesives may crack, peel, or transfer excessive stress into delicate components. The product uses a 1:1 mixing ratio and provides a pot life of approximately 10 to 11 minutes at 23°C. Its set time is about 40 minutes, while useful operating strength can develop in approximately 24 hours. These characteristics support controlled dispensing, accurate positioning, and efficient production planning.
Key Benefits of CEMEDINE EP001K Elastic Epoxy Adhesive
CEMEDINE EP001K Elastic Epoxy Adhesive balances peel resistance, shear strength, elasticity, and broad substrate compatibility. The base resin is milky white and the hardener is light yellow. Typical viscosity values are approximately 14 Pa·s for the resin and 18 Pa·s for the hardener at 23°C. After curing, the material has a typical Shore A hardness of 72, elongation at break of about 200%, and an elastic modulus of approximately 3.2 MPa.
The flexible cured layer helps the joint absorb movement instead of becoming excessively rigid. This makes the adhesive suitable for bonding materials with different coefficients of thermal expansion. It is designed for locations exposed to vibration, changing stress, thermal cycling, or internal strain. The product offers good adhesion to general-purpose and engineering plastics, including PBT and PPS, while also supporting metal-to-metal and plastic-to-metal assembly.
Applications for CEMEDINE EP001K Elastic Epoxy Adhesive
CEMEDINE EP001K Elastic Epoxy Adhesive can be considered for electrical and electronic component bonding, potting, housing sealing, precision equipment, optical equipment, glass assembly, automotive electronics, battery components, and construction-related parts. It is useful for joining battery cells to housings, sealing converter or electronic-control-unit enclosures, bonding sensors and camera components, and assembling parts exposed to vibration or repeated temperature changes.
The adhesive may also support engineered-plastic housings, non-ferrous metal parts, and mixed-material structures requiring high peel and shear performance. Because adhesion depends on plastic grade, coating, surface treatment, bond geometry, and service environment, users should test production materials before mass use. Critical assemblies should be validated under the intended load, temperature, humidity, chemical exposure, and operating cycle.
How to Apply CEMEDINE EP001K Elastic Epoxy Adhesive
Before applying CEMEDINE EP001K Elastic Epoxy Adhesive, remove oil, dust, moisture, rust, oxide, mold-release agents, and other contamination from both surfaces. Dispense equal amounts of base resin and hardener onto a clean mixing surface or use suitable two-component dispensing equipment. Mix thoroughly until the appearance and consistency are uniform, then apply the adhesive within the working time.
Join the parts, confirm alignment, and secure the assembly with clamps, tape, or a suitable fixture. Maintain stable contact while the adhesive sets, and avoid applying service loads before sufficient curing has developed. For repeatable production, control the mixing ratio, adhesive quantity, bond-line thickness, assembly time, fixture pressure, temperature, and curing conditions.
Storage and Safety of CEMEDINE EP001K Elastic Epoxy Adhesive
Store CEMEDINE EP001K Elastic Epoxy Adhesive in its original sealed packaging according to the current product label and safety documentation. Keep resin and hardener tools separate to prevent contamination. Use the product in a ventilated workplace, avoid skin and eye contact, and wear suitable personal protective equipment. Always review the latest safety data sheet before industrial use.
For buyers seeking a flexible two-part adhesive for demanding mixed-material assembly, CEMEDINE EP001K Elastic Epoxy Adhesive offers convenient 1:1 mixing, strong adhesion, high peel resistance, and durable performance under vibration and thermal movement. Explore our industrial elastic epoxy adhesives for additional solutions for engineering plastics, metals, glass, electronics, automotive components, and precision equipment.
