Kafuter K-1668 Flame Retardant Electronic Adhesive is a yellow, high-viscosity solvent-based adhesive developed for positioning and securing components in electrical and electronic equipment. Its thick, non-flowing consistency supports controlled application on vertical circuit boards, component bases, connectors, coils, capacitors, cables, and power-supply assemblies. The material combines fast surface drying, electrical insulation, flame-retardant performance, and practical cartridge or bulk packaging, making it suitable for manufacturing, maintenance, appliance assembly, electronic repair, and industrial production.

Table of Contents

Kafuter K-1668 Flame Retardant Electronic Adhesive Performance

Kafuter lists K-1668 in its solvent-adhesive range and specifies a viscosity of approximately 130,000 to 250,000 mPa·s. This high-viscosity profile helps the adhesive remain where it is dispensed instead of running across a board or down an upright component. The manufacturer also lists a drying time of less than ten minutes under its reference conditions. Actual drying and strength development depend on applied thickness, airflow, temperature, humidity, substrate porosity, and the amount of solvent that can escape from the joint.

The product is designed to provide electrical insulation and flame-retardant performance after proper application. These characteristics make it useful around components that require mechanical support without creating an electrically conductive path. Kafuter also describes the material as suitable for vertical coating, allowing operators to form reinforcing beads and localized fillets around parts that may experience vibration, movement, or handling stress.

Electronic Component Fixing and Reinforcement Applications

Kafuter K-1668 Flame Retardant Electronic Adhesive can be used to position capacitors, secure coils, stabilize connectors, reinforce wires, fix cable outlets, support transformers, and hold selected components on printed circuit boards. It may also be applied in household appliances, control equipment, power supplies, communication devices, lighting products, audio equipment, chargers, and industrial electronic modules. The yellow appearance provides visible coverage, helping operators inspect bead placement during production and repair.

The cured adhesive can help reduce movement caused by vibration or transportation and can provide additional support around taller or heavier components. It is not a substitute for correct mechanical design, soldering, electrical spacing, or load-bearing hardware. Adhesion varies with plastic grade, metal finish, board coating, solder mask, contamination, component geometry, and operating environment, so representative testing is required before commercial approval.

7 Benefits of Kafuter K-1668 Flame Retardant Electronic Adhesive

High-viscosity application: Stays in position on vertical boards and irregular component surfaces.
Fast surface drying: Manufacturer reference data lists a drying time below ten minutes.
Electrical insulation: Supports component fixing around compatible electrical assemblies.
Flame-retardant performance: Designed for selected electronic and appliance applications.
Reduced stringing: Controlled rheology supports cleaner manual and production dispensing.
Visible yellow color: Helps operators confirm coverage and application position.
Multiple package options: Available in 85 g tubes, 2.5 kg cans, and 15 kg drums.

Surface Preparation and Application Guidance

Clean the target surfaces and remove oil, grease, dust, moisture, oxidation, release agents, flux residue, and loose contamination. Apply a controlled bead to the component base or required fixing area. Ensure the adhesive contacts both the component and the supporting surface, but keep it away from electrical contacts, adjustment points, heat-sensitive areas, ventilation paths, and parts that may require later servicing.

Allow adequate ventilation and drying before powering, packaging, or testing the assembly. Thick deposits, enclosed cavities, and low-airflow areas require longer because solvent must escape completely. Production qualification should evaluate initial positioning, full strength, vibration resistance, electrical insulation, flame requirements, temperature exposure, humidity, and compatibility with the actual board, component, coating, and cleaning process.

Packaging, Handling, and Official Product Resources

Kafuter lists K-1668 in 85 g tubes for workstation use and in 2.5 kg cans or 15 kg drums for higher-volume dispensing. Select packaging according to daily consumption, application equipment, solvent-control requirements, and inventory turnover. Keep containers tightly closed when not in use to limit solvent loss, viscosity change, skin formation, and contamination.

Because K-1668 is solvent based, use suitable ventilation, ignition control, protective equipment, and approved workplace procedures. Consult the current safety data sheet before handling, storage, transport, spill response, or disposal. Do not use the product near flames, sparks, or energized equipment while wet.

Review the official Kafuter K-1668 product information and the official Kafuter solvent and water-based adhesive range for current viscosity, drying, application, and packaging details.

Explore our electronic component fixing adhesives for additional products used on capacitors, coils, wires, connectors, and circuit boards. Browse our flame-retardant electronic adhesives for electrical insulation, vibration support, and appliance assembly. Contact our sales team for quotations, package availability, technical documents, samples, bulk quantities, and export support.